Invidia offers products known for their outstanding quality, and each finished piece is a work of art that sets them apart from the competition. For anyone looking to take their vehicle to the next level, Invidia is a name to remember. So, a cat back is used to indicate an upgrade to the stock exhaust system. And anyone looking to improve their ride should strongly consider a cat back exhaust system. This pipe will connect your mk1 downpipe that we sell for  1.8t, vr6, or aba 2.0, to the catback exhaust system. Therefore you need to check with your local state laws for legality.

By running pipes from the catalytic converter to the muffler and from the muffler to the exhaust tip, cat back exhaust systems improve exhaust gas flow, providing small performance boosts. However, your performance gains may be limited if your catalytic converter restricts gas flow, as a catback exhaust system is installed ‘downstream’ of the converter. Header-back systems are increasingly rare, namely because of modern emissions systems. Since removing your vehicle’s factory emissions components is highly illegal, the previous two options are more common. However, header-back systems are still available for some older, pre-emissions applications. In these cases, header-back systems offer more performance and volume than cat-back or axle-back systems; however, they’re also the most expensive and the most challenging to install.

If you have modified your 4×4 with lifted, lowered, or air type suspension systems, you can opt for a specially designed cat-back system with more pipe curvature before the rear axle. This is necessary for off-roading as it allows a higher degree of wheel travel and greater clearance for reduced-height springs and airbag suspensions. The custom exhaust systems available let you pick from a selection of pipework that allows you to adjust the exhaust to suit your noise preference. Are you looking to boost the power and efficiency of your vehicle?

So listen up and checkout this MBRP Black Series 3" Dual Cat-Back Exhaust on a 2021 LT1 Camaro. This is the main path to completing your full exhaust upgrade. And when it's time to perform maintenance that required the removal of your exhaust system make sure that you use new gaskets if your existing gaskets have too much heat damage. And check out the rest of the exhaust options to fully protect and support your exhaust beyond your cat-back setup.

CORSA does not recommend or recognize purchases and installations on unspecified vehicles. ARK Performance is a leading manufacture that develops the best cat back exhaust systems, downpipes, test pipes, and hi-flow cats for all car enthusiasts. Using custom designed straight through mufflers for flow - without the noise level of a track car. From a company that’s as committed to your satisfaction as to sonic excellence. A catback exhaust system is a great way to improve the sound, performance, and emissions of your vehicle. If you are looking for a way to improve your vehicle, a catback exhaust system is a great option.

Featuring virtually indestructible 100% stainless steel, our patented TorqueTube headers maximize exhaust extraction to haul you up the grade. This Takeda cat-back exhaust system by aFe POWER delivers superior performance, quality, and good looks. By replacing the rear section of your exhaust with a quality cat-back car performance exhaust system, you can reduce the backpressure and allow your engine to cycle with more speed and efficiency. Thanks to their larger diameter pipes and high-quality mandrel bends, a good cat-back exhaust system will increase the efficiency of your car’s exhaust system, and with increased efficiency comes increased power. The exhaust system in your car directs fumes away from yourself and your passengers, improves engine performance and fuel consumption, and controls cabin noise.

As a result, our popularity has increased, and we work tirelessly to maintain our quality systems while fulfilling orders. Please be aware that while we typically exceed our estimated wait times, we have been successfully operating for three years and no customer has ever been left without their system, or a cancellation/refund. At Rae, we are expanding our team and investing in additional resources and machines to ensure we stay at the forefront of innovation. With our ambitious plans, we are on track to meet demand and increase our inventory of premium parts by the end of the year. Please note that purchasing this product is agreeing to understand this concept. Amplify your vehicle's performance and sound with Full-Race's premium Exhaust systems - reliable power and efficiency harmonize with a brand that’s trusted for quality and performance.

Unlike your stock system, CORSA exhaust systems don't utilize performance-robbing restrictions that reduce airflow, such as chambered designs, baffles or spring-loaded valves. With wider tubing and our mandrel-bent design, your new full exhaust system will allow for reduced backpressure and provide cleaner oxygenized air to your engine. You'll see benefits like increased horsepower, torque boost and better fuel economy.

From Overland Series to our all-new SPEQ Series, explore MagnaFlow's latest performance exhaust systems designed for the 2024 Toyota Tacoma. Aftermarket cat-back exhaust upgrades are a relatively simple way to increase your vehicle’s power. Typically these upgrades involve installing wider piping with fewer sharp or sudden bends as a way to reduce backpressure. Backpressure is pressure opposing the desired flow of exhaust gasses. The more you are able to reduce backpressure, the more efficient the system will be, and ultimately your horsepower will increase. Cat-back exhaust refers to any part of the exhaust system that’s behind the catalytic converter.

This exhaust is going to sound the deepest and give you some nice pops and bangs, while also giving you real world WHP and TQ gains. We’ve seen as much as +12 WHP when we tested our turbo-back for the 2022+ Honda Civic! For this version, we do recommend a tune and a device like a Ktuner V2 or Hondata Flashpro to take full advantage. Since the OEM catalyst is replaced with the downpipe, the Turbo-back system is sold for Race Use Only. A cat-back exhaust system replaces the stock exhaust components from the catalytic converter back to the exhaust tips.

When it comes to improving your vehicle’s performance, you have two options. However, stainless still can be very expensive, as opposed to aluminized steel which is very affordable. It is also resistant to corrosion, just not to the level of stainless steel. Since there is no back pressure and the diameter is large enough, the engine will not use a lot of energy to push the exhausts out. While getting a cat-back performance exhaust system can be pricier initially, it can save on a lot of costs in the future. These exhaust pipes are usually wrapped in sound-absorbing materials, mostly fiberglass packing.

This is the 3rd Gen Toyota Tundra Borla S-Type Cat Back Exhast with Chrome Dual Tips. Borla manufacturers some of the best Toyota Exhaust systems, and this S-Type 2022+ Tundra Exhaust is no different, featuring the Merge X-Pipe for increased performance adn improved sound. The Carven-R series Performance Muffler delivers an aggressive sound with a refined tone. This unique pack-less (Patent# D802,507) muffler design is one of its kind. Stand out from the crowd with a performance exhaust system that sounds great. Save big on that signature MBRP sound during Pick Up Your Sound.

A dual exit on the other hand, is just a single exhaust system but with two exhaust tips. This is because, with a cat-back exhaust system, you will experience a significant increase in your fuel economy. The tone provided by different cat-back exhaust systems varies from one system to another.

The bolstered heated front seats and contoured rear bench are upholstered in Onyx and Red leather. Appointments include a Blaupunkt 11-speaker sound system, a CD stereo, cruise control, a leather-wrapped shift lever, and automatic climate control. Whether you're seeking Upgraded Turbochargers, Axle-Back exhaust systems, Coilovers, or SubiSpeed Headlights we have you covered. The truck is based on the F-150 Lariat 4x4 SuperCrew and Shelby plans to limit production to 800 examples for the 2024 model year. Pricing starts at $130,000 for the naturally aspirated version and $139,995 with the supercharger attached. The urea solution is also referred to as diesel exhaust fluid (DEF).

The new Large Bore-HD exhaust is engineered to perform in the most extreme environments. This system is constructed from mandrel bent 4" stainless steel tubing for maximum flow, increased horsepower, increased torque and lower EGT's. This system is available in 4" cat-back with muffler. Large Bore-HD exhaust systems are the perfect combination of performance, fit and value. For over 40 years, MagnaFlow has maintained its position at the forefront of high-end catalytic converter and performance exhaust manufacturing. MagnaFlow stands by its products with industry-leading warranties in service of its mission to provide the highest quality exhaust experience from start to finish.

In this article, we are going to focus on cat back exhaust systems, and the main ten reasons that we have discovered as to why they are worth a look. If we know our car lovers, finding the right exhaust system for a car or truck is about getting more power without spending a fortune, and cat back exhaust systems tick a lot of boxes. Here is a pic of a converter and looking through the high flow core. Unleash the potential of your big displacement K motor with our high flowing 3" Header Downpipe.  This product eliminates BOTH OEM catalytic converters.  Available Catless or with a single High... We are proud to offer a wide range of completely custom, ready-built exhaust systems and parts at competitive prices with a lifetime guarantee. Contact Bradley’s Auto Service in Red Bank, NJ, today to get a quote for fitting, testing, and tuning your new exhaust system for maximum performance gains.

These two work together to offer better flow and allow the system to breathe better. We are one of few brands that own our factory thus enabling us full control over the manufacturing process, selection of raw materials, and construction techniques. Install your IE catback without any permanent modifications or installation hassles. The installation process is straightforward and accomplished with standard mechanic tools.

Since 2003, we have specialized in building BMW M-models (and Tesla) with a refined selection of industry-leading, high quality products. Our 8,000 sq/ft installation facility and shipping headquarters is located in Anaheim, California. IE's advanced DroneTrap technology captures the pulse waves responsible for your B9 3.0T engine's exhaust note and draws them into dual mathematically tuned resonators. The internal ports are engineered to resonate these waves against each other in a process that selectively cancels out those responsible for annoying drones.

Make sure your Subaru, Nissan, Honda, or Toyota is outfitted with a top notch exhaust system from Racing Exhaust System. Some are ideal for normal vehicles while others are better for high-performance engines. Products manufactured by REMUS without (EC-)approval are only eligible for usage at motor sport events or tests within the meaning of KFG 1967.

Typically, that includes a mid-pipe, muffler, tailpipe and tips. Cat-backs generally yield increases in performance, due to the more efficient flow of exhaust through upgraded parts like larger diameter tubing and better flowing mufflers, as well as improved sound and reduced weight. For starters, the "cat" in catback exhaust system is short for "catalytic converter", a central part of your car’s emission control system, which cat back exhausts are fitted behind, hence the "back". This relatively simple mod helps to free up exhaust gas flow and improve the noise of your engine by swapping out part of your exhaust system with a specially designed car performance exhaust system. These three reactions occur most efficiently when the catalytic converter receives exhaust from an engine running slightly above the stoichiometric point. For gasoline combustion, this ratio is between 14.6 and 14.8 parts air to one part fuel, by weight.

There are loads of options, all offering different benefits, and the amount of research you do can quickly turn to frustration when you realise the minuscule differences between the many options. OE-quality exhaust products engineered for today's medium-duty and heavy-duty vehicles. The single 60mm is split into twin 50mm pipes to the twin silencers.

The purchasers are entirely responsible for informing themselves of applicable California laws and to comply with those laws. Mishimoto exhaust systems are designed for a bolt-in installation. From classic American muscle cars to the newest off-road capable rigs, we’ve got you covered. Browse our most popular performance car, truck and SUV exhaust systems to find the ultimate exhaust experience for your ride.

The team at Sandgate Auto Electrics are well-versed in all things automotive which has led to them becoming the go-to for car lovers in the northern suburbs of Brisbane, South East Queensland. As a family owned and run company, who are local residents themselves, we have gotten to know their loyal clientele and love helping them with the repairs and modifications. Each "receiving" 50mm pipe is crushed in half, squeezed next to the other and welded to the 60mm "feed" pipe. We hope you enjoyed this lighter take from 27WON and find the information helpful the next time you shop for an exhaust system.

Beyond these incremental advantages, there’s not much to tell cat-back and regular exhausts apart, as they are commonly made from the same types of materials in roughly the same shape. Most newer vehicles have electronic fuel injection systems, and do not require air injection systems in their exhausts. Instead, they provide a precisely controlled air-fuel mixture that quickly and continually cycles between lean and rich combustion. Depending on your make and model, cat back exhaust systems can lead to an increase in fuel economy. The engine doesn’t have to work as hard pushing exhaust gases through the piping which reduces its load and leads to higher efficiency and MPG. For car enthusiasts and performance drivers, upgrading the exhaust system of a vehicle is a no-brainer.

Walker is your one-stop exhaust shop, offering a full line of mufflers, pipes, hardware and accessories. Cat to Y pipe intersection showing after cat O2 sensor location. This qualifies as one of the STRANGEST stock exhaust parts I have seen. For some reason Toyota/Lexus decided to weld a straight section of 60mm pipe to the cat outlet flange, angle cut it, weld a 50mm pipe pipe that has its last couple of inches expanded to 60mm and match angle cut. Also note the O2 placement is in the 50mm sections of the Y pipe where the sensor tip takes up a good portion of the available flow area.

Because the success of a catback exhaust system depends on various factors – like catalytic converter restrictions, engine power, etc. – there’s no easy way to calculate how much horsepower you stand to gain. If you have a restrictive exhaust, then a cat back exhaust could massively improve your car’s performance, and contrastingly, if your exhaust already flows well, then a cat-back won’t be much of an upgrade. In Colorado, it is illegal to select a catalytic converter for installation based solely on vehicle weight and engine size. Converters in this catalog are based on Executive Orders issued by the California Air Resource Board and must be used in accordance with this information.

Our exhaust system uses larger piping compared to the factory exhaust system, yet weights 5 lbs. The factory system uses 2.56" piping, which reduces to 2.36" before splitting, greatly diminishing the overall diameter of the system. Finally, our system’s 4" exhaust tips dwarf the factory 3.15" tips, giving the rear of the vehicle a sportier look. Beautifully hand-crafted T304-stainless-steel components adorn the system with stunning TIG-welding throughout.

Therefore, they are placed as close to the engine as possible, or one or more smaller catalytic converters (known as "pre-cats") are placed immediately after the exhaust manifold. Founded in 1988, Steeda is the leader in Ford performance products. We specialize in the engineering and manufacturing of parts for the Ford Mustang, Bronco, Bronco Sport, Explorer, Escape, Fusion, Focus, Fiesta, Ford Trucks, and more!

A faulty exhaust system can cause a decrease in power, acceleration and fuel efficiency, as well as potentially exposing drivers and passengers to harmful gases, so issues should be fixed immediately. We have a wide range of exhaust systems in stock – browse our range and find the correct exhaust system for your car below. There are many distinct and differentiable features to each of many cat back exhaust systems, meaning it’ll be easys to find a do-it-yourself cat back installation. The modifications directly bolt where the original exhaust is, so there won’t need to be excessive installation. You’ll have everything you need to replace the exhaust with the pipes, muffler, and tips that come with a DIY package.

Namely, it replaces the rear axle-back and tips and then a portion of what we refer to as the mid-pipes. This system is emissions friendly and doesn’t require any tuning. In New Jersey, vehicles must pass emissions testing to ensure they meet environmental standards. Since cat-back exhaust systems do not modify the catalytic converter or engine management system, they generally do not affect a vehicle’s ability to pass emissions testing.

Explore renowned manufacturers such as Borla, Invidia, and HKS, known for their exceptional craftsmanship and exhaust system expertise. FTSpeed's cat back exhausts are designed to perfectly fit your sports car, delivering noticeable gains in both power and aesthetics. Elevate your vehicle's performance and sound with our premium cat back exhaust systems. Cat-back exhaust systems typically feature a muffler, and sometimes not, and these will have piping that will route to your catalytic converter. The piping will have larger bends that are as straight as possible to provide an unobstructed exit path for the exhaust gases.

Different exhaust systems offer different noise levels and tones, but how? Sound quality and overall loudness of an exhaust system can vary significantly depending on the pipe diameter, size and design of the muffler, resonator inclusion, and the number of outlets. For this reason, all systems sold on RealTruck are filtered by noise level, including loud, moderate, and quiet. From the factory, most manufacturers employ small-diameter piping, restrictive mufflers, and noise-reducing resonators, significantly smothering exhaust flow and sound quality. A front pipe back system replaces a few key components of the OEM Honda or Acura exhaust found on your EX, Touring, Si, or A-Spec that are after the Front Pipe (the pipe that goes under the engine).

Glasspack mufflers do not have extra sound-absorbing material. So, in order to absorb sound, they use the glass layer and packing. But if you are making your order on partcatalog.com, you can always inquire about the recommended tube diameter for your exhaust system by providing your make and model. This can lead to a significant decrease in torque and horsepower as well as rpm.

Shelby also gives the truck some off-road chops by installing a BDS 3.0-inch lift kit, Fox 2.5-inch internal bypass dampers, and performance rear traction bars. The truck also sits on a set of 22-inch Shelby wheels wrapped in 35-inch all-terrain tires. The new 2024 Ford Shelby F-150 packs up to 785 hp, or more power than many supercars. That's with an available supercharger for the truck's 5.0-liter V-8. Buyers can also opt for a naturally aspirated version where the V-8 keeps its stock 400-hp rating.

The APR Catback Exhaust System personalizes your vehicle’s looks, sound and performance. You get the only the best with SPD's 3" resonator 2015 f250 egr delete kit pipes. These 304 Stainless Steel pipes are .. SPD's high performance stage 1 resonator cat-back pipe replaces your factory resonator pipe with a t..

Let’s look at the top ten reasons why a cat back exhaust system may be right for you. While a cat-back exhaust system includes all components from the catalytic converter to the exhaust tips, an axle-back system only replaces parts from the rear axle to the tips. Axle-back systems are generally easier to install and less expensive but offer more limited performance improvements and sound changes compared to cat-back systems. All our performance exhaust systems are designed with you in mind, and we cater to an ever-expanding range of vehicles. We believe in continuous evolution, and our research & development team work throughout the year to deliver the most in demand solutions to all your performance exhaust requirements.

An upstream air injection point, ahead of the catalytic converter, is also sometimes present to provide additional oxygen only during the engine warm up period. This causes unburned fuel to ignite in the exhaust tract, thereby preventing it reaching the catalytic converter at all. This technique reduces the engine runtime needed for the catalytic converter to reach its "light-off" or operating temperature. Many vehicles have a close-coupled catalytic converter located near the engine's exhaust manifold. The converter heats up quickly, due to its exposure to the very hot exhaust gases, enabling it to reduce undesirable emissions during the engine warm-up period.

The performance parts available at Steeda include lowering springs, wheel spacers, spark plugs, brake kits, and many more. Choose from our Ford automotive parts today so that you can keep your ride in great condition. When it comes to picking a cat back exhaust system, you will likely be choosing between stainless or aluminized steel. The majority of the performance systems are made from stainless steel which is favoured as they won’t oxidize and corrode over time like traditional steel can.

They directly bolt on to where the original exhaust sits and do not require any further modification. Cat back exhaust systems come with exhaust pipes, muffler and exhaust tips, so you have everything you need to replace the exhaust. The cat back is the section of the exhaust that runs from the outlet of the catalytic converter to the exhaust tips. Exhaust systems that include this often feature a large pipe running from the converter to the muffler, with mandrel-bent turns and glasspacks for reduced back pressure. Your go-to spot for information on the exhaust system, as well as mufflers, catalytic converters, pipes and sensors.

You also need to be careful when tightening the bolts on the cat back. Over-tightening can damage the system, so just make sure they're tight enough to hold everything in place. It's important to make sure that the cat back is properly aligned with the exhaust pipe. If it's not, you could end up with an inefficient or even dangerous exhaust system. Competitors often rely on generic silencers or gimmicks that claim to cut out drone without any real knowledge or development involved.

One main reason for choosing to remain with a stock system is because it comes already installed on your vehicle. You should know the difference between a dual exhaust and a dual exit exhaust system. But it is easy to mistake a dual exit exhaust for a dual exhaust system. The materials are often 304 stainless steel or aluminized steel. The stainless steel is usually coated in special metals that make it corrosion-resistant. This means there will be a reduction in the amount of load on the engine, leading to higher mpg and fuel efficiency.

Video Features Options Short video of our 3" Catback Exhaust for the 07+ Honda Civic Si Sedan. Note that this was installed on a naturally aspirated setup (stock header and... Already own an Ultimate Racing Performance Muffler and want to upgrade to a full Catback system. For information about our other auto repair services, please refer to our comprehensive guide. But both cons of a resonator are not present with a cat-back exhaust system. For the noises that the muffler fails to get rid of, the resonator eliminates them. As a result, they are fitted with both a muffler and a resonator.

The buyer is solely responsible for obtaining the permissions where applicable required by the applicable law for the intended purposes/usage. In no event a whatsoever claim shall be constituted by the buyer against REMUS and its affiliates arising from or in connection with required approvals for public road usage. Take your stock or modified Colorado/Canyon to the next level with a Mallett Performance Cars exhaust system today.

And a lot of people think that gearheads mess with it just to make our cars sound louder. Another problem is that the gaskets and seals can degrade over time, resulting in leaks. These leaks can usually be fixed by replacing the relevant seals and gaskets.

Take up to $150 off gas truck exhaust and up to $75 off diesel truck exhaust and components starting July 1st, 2024 – for a limited time only. Evidently, a cat back exhaust system has many benefits all while being a quick, easy, and affordable solution that will transform your car. If you have any questions about what a cat back exhaust system can do for you, don’t hesitate to contact us at Loper’s Performance Center.

The cat back system’s pipes have a larger diameter than a standard set. So, your vehicle will get to perform better at a fraction of the work it outputs. An axle-back exhaust system will replace the components from the rear-axle back. While axle-back CORSA exhausts will provide some slight performance gains, their primary focus is to influence your exhaust notes. Different axle-back exhausts will offer different exhaust notes, so it's best to browse our entire selection to find the sound most suited for your vehicle.

Cat-back exhaust systems will include any pipes that run from the catalytic converter to the muffler, the muffler itself, any pipes that may run from the muffler to the exhaust tips, and the exhaust tips themselves. Some cat-back exhaust systems have a muffler f250 delete kit, which means no muffler is included. This is typically found on vehicles that function primarily for off-road use; it's not standard on daily driver vehicles and is even illegal in some states.

Combined with our five different tip options, we've got you covered. We’ve had decades of experience perfecting exhaust style and technology and have developed custom exhaust systems considered too ‘niche’ by competitors. Many exhaust manufacturers use 400 series stainless steel to reduce costs and pad their profits. Additionally, the Maverick systems by Thermal offer a range of upgraded tip options that owners can choose from or change over time. Getting an upgraded cat-back exhaust system for your truck can enhance your performance and produce a great sound. Then there’s poor fitment and the dreaded drone that all too often accompanies aftermarket exhausts.

Even a small leak can cause problems down the line, so it's better to be safe than sorry. By following these simple tips, you can ensure that your cat back installation goes smoothly and without any issues. When it comes to cat back installation tips, there are a few things you need to keep in mind.

Everything you love about our MK7 Golf range has been re-engineered to suit MK7.5. Enjoy an unparalleled experience, power and sound output coupled with a seamless fit. Trucks are all about dependability and capability, which is why MagnaFlow engineers every one of our durable, corrosion resistant stainless-steel exhausts to last the lifetime of your vehicle. One of the things you would appreciate about the axle-back exhaust system is that it offers better sound improvement.

Adding Ford F-150 Cat-Back Exhaust system to your truck is a quick, relatively cheap and easy way to extract more performance. We offer a number of high-quality systems from excellent manufacturers, so you can rest assured that whatever choice you make will look and sound like it belongs on your F-150. The Flowmaster Outlaw catback system has dual black tips that exit on the side, adding an extra aggressive look to your vehicle. Or go with a Magnaflow system for a signature rumble that everyone loves. Aftermarket performance exhausts are exhaust systems meant to replace the stock exhaust and offer more power and better tone to your engine. All our products are made from 304L "Aircraft" Grade stainless steel.

Less restrictive catalytic converters paired with a cat-back exhaust system will offer high performance and power. Though, the level of horsepower gained is not constant across all cat-back systems. It depends on the quality and performance of the catalytic converters. Because of the better flow of exhausts resulting from the mandrel-bent tubing and the larger diameter piping, cat-back exhaust systems manage to offer better performance. IE offers catback, downpipe, and midpipes upgrades to replace individual sections of your exhaust. Installing variations of these parts allows you to dial in your exhaust volume to your preference, from sporty to aggressive.

Finished in Panther Black Metallic over Onyx and Red leather, the car is powered by a 6.2-liter V8 linked with a six-speed automatic transmission and a limited-slip differential. Purchased by its current owner in February 2022, this G8 GXP is now offered with a reproduction window sticker, service manuals, a car cover, the removed exhaust system, a spare set of wheels, and a Michigan title. A catalytic converter is an exhaust emission control device which converts toxic gases and pollutants in exhaust gas from an internal combustion engine into less-toxic pollutants by catalyzing a redox reaction. Catalytic converters are usually used with internal combustion engines fueled by gasoline or diesel, including lean-burn engines, and sometimes on kerosene heaters and stoves. Whether you’re accelerating up a highway on ramp or passing slower traffic, improved acceleration lets you get up to speed more quickly. Gain horsepower, increase torque, and give your truck a more aggressive exhaust note with a new exhaust system.

The difference is that the dual exhaust system has two exhaust systems on one vehicle. Meaning, when modifying your exhaust, never start from the front of your turbocharged vehicle with a downpipe or with headers on your naturally-aspirated platform, you will create a bottleneck in the flow. By starting with a cat-back first, your exhaust gases will flow more freely if the rest of your system is stock.

Rattling or knocking noises from your vehicle are the most common signs that you need a new exhaust. Any rust on the exhaust can also be a sign that an upgrade is due. When you bid we pre-authorize your credit card for the service fee (this helps prevent fraud). If you win the auction, your card will be charged for the service fee and you pay the seller directly for the vehicle. If you don't win, your existing pre-authorization will be released.

The products of REMUS Innovation Forschungs- und Abgasanlagen Produktions GmbH („REMUS") are distributed worldwide. This applies equally to products approved in Austria, which are subsequently manipulated, modified, edited or otherwise interfered or changed by the respective buyer, so that it no longer has its original condition. Discover MagnaFlow's latest evolution in performance exhaust technology. Stainless steel is the most popular choice for cat backs because it is durable and has a deep, throaty sound. But if you're looking for something lighter weight, you can also find cat backs made out of titanium. So, when it comes time to choose the right cat back for your car, keep these three things in mind and you'll be sure to find the perfect fit.

The only difference is that it features straight perforated pipes. The original exhaust systems focus more on just reducing the sound and not shaping it to give it that desired deep growl. One function shared with both the axle-back and the cat-back exhaust systems are shaping your vehicle’s tone.

Decades later, Gale and the team are not only innovating, patenting products, and setting the bar for aftermarket performance manufacturers, we're also sharing our secrets with the world. The 6.2-liter LS3 V8 was factory rated at 415 horsepower and 415 lb-ft of torque. It is used to expel harmful gases and substances from your engine; without it, the car could experience a build-up of fumes.

Adding a dual exhaust to your vehicle can have a number of advantages. Functionally, two exhausts can improve engine performance and reduce emissions. Aesthetically, it has the sporty look that some people search for in a vehicle. Catalytic converters require a temperature of 400 °C (750 °F) to operate effectively.

It's more than our precision-fit or full engine-to-tailpipe product offering, Walker sets the standards. From mild rumble to wild roar, upgrading your exhaust will improve the sound of your truck and help it to stand out from the pack. This direct-fit SPEQ Series system bolts on to your Tacoma easily thanks to the extensive use of 3D scanning during development to ensure OEM-like fitment.

Because the engine won’t generate as much fumes and doesn’t need to work as hard to eliminate or minimize the fumes, your car will run better, saving you mileage. A benefit like this will improve the longevity of your car and even save you money at the gas pump. At Bradley’s Auto Service in Red Bank, NJ, we can build a completely custom exhaust system for your vehicle, including cat-backs. We will work with you to create your exhaust exactly the way you want it, with any combination of look, sound, feel, power, or muffler at your fingertips.

When the exhaust mode is placed in "Sport" mode the exhaust system broadcasts an "Xtreme" level sound 6 decibels louder than the stock exhaust system. As the driver adjusts the exhaust mode to the "Normal" level, the exhaust produces an exhaust note more closely resembling a CORSA "Sport" level exhaust note. At Mishimoto we offer a variety of products such as intercoolers, catch cans, cold air intakes and more. Trust in Mishimoto's expertise and commitment to quality to deliver exceptional products for all your automotive needs. Mishimoto exhaust systems utilize high-flow mufflers for minimal flow restriction.

Federal Catalytic Converters are not legal for sale, installation or use in the state of California. It should be noted that a split system will often provide an aggressive noise increase, and some designs will split the two pipes to opposite sides of the vehicle. If you are looking to save a little money but still get most of the benefits of a cat back exhaust system, however, aluminized steel may be the way to go. Made from traditional steel that’s been coated on all sides with aluminum-silicon alloy, these systems are very strong thanks to the metallurgical bond which still provides a level of corrosion resistance. While the aluminum coating reflects heat well, the steel can corrode if the aluminum layer is chipped or scraped off. Most cat-back systems will come in either an aluminized or stainless steel version.

The first widespread introduction of catalytic converters was in the United States automobile market. The exhaust system is crucial to a car’s performance, especially the catalytic converter which can go bad if it’s overworked. A stock exhaust system strives to minimize the car’s materials while maximizing space. This means that the exhaust system’s performance can suffer, having to work harder with less horsepower.

Not only do our products boost performance and optimize exhaust flow, but we also add a touch of personalization to your ride. Find the perfect performance exhaust system compatible with Ford, 2012 ram 3500 egr delete kit, Chevy/GMC, Jeep, and more. Our patented design outflows all other exhausts on the market. The CORSA Performance GT350 Active valve exhaust system allows the driver to flexibility of having one exhaust that produces both an Xtreme and a Sport sound level.

There are several factors to consider when selecting an exhaust system for your vehicle, including noise level, finish, price, style, and installation difficulty. As you move through the versions here, you’ll notice that the more complete the system, the more expensive it becomes. In exchange, you'll get more performance and sound benefit out of the system. To sweeten the pot, our exhausts come with significant savings once you start bundling multiple pieces together.

The time and money you spend are a big investment, and we want to help you make the best decision for your driving dreams. Typically, a cat-back exhaust system will increase your car’s horsepower by somewhere between 5 and 50 brake horsepower. This will vary greatly depending on the condition of your exhaust and engine, so you should ask your mechanic if getting a cat-back exhaust is the best way to improve the performance of your car.

Our design concept is to provide a sporty and authentic exhaust note, while improving performance, and enhancing the visual styling of your vehicle. Each product is carefully developed, and then expertly crafted by our own factory. The whole reason I decided on an IE cat back vs mbrp or AWE was the craftsmanship. However I do live in warm and sunny south Florida so I know it will only see tons of rain but never salt or snow unless it’s an impromptu trip. I love the lil burble crack when going down in rpm and down ship. I wish it were a little louder but if that we my main goal I’d have just gutted cats n resonators n left stock mufflers.

From the inception of the small block Cobra, Carroll Shelby intended to build a race version of his lightweight roadster; its ultimate iteration was the 289 FIA roadster. Special Edition Shelby F-150 Super Snake celebrates Carroll Shelby's passion for performance trucks. Shelby American is celebrating the 100th anniversary of Carroll Shelby's birth with a performance street truck to honor the ledged.

Exhaust systems are integral to your ride’s performance; these amalgamations of piping, mufflers, and resonators carry exhaust gasses from your vehicle’s exhaust manifolds to the tailpipe. Dual muffler section upgrade designed to bolt up to the OEM midpipe   Features Bolts on to factory midpipe! 3-inch 304 stainless steel piping Dual high-flow mufflers with straight through... Reducing back pressure is the key to improving performance with a cat-back exhaust system. By allowing exhaust gases to exit the engine and flow through the system more freely, the engine runs more efficiently. This efficiency can translate to better throttle response, increased horsepower, and even improved fuel economy in some cases.

Don’t deny yourself the perfect blend of sound and performance any longer. Give our team a call today for a cat-back exhaust system that will unleash the potential of your Maverick. I'm very pleased with this [Thermal R&D] exhaust on my Maverick. Loud enough to let the people around you know you have an exhaust but not so loud as to wake up your neighbors at 4 am. During cruising you can barely hear it inside but it wakes up when you step on it. Definitely not obnoxious but gives the truck a performance sound.

SPD's 304 stainless high performance resonator cat-back pipe replaces your factory resonator pipe wi.. SPD's high performance stage 2 resonator cat-back pipe replaces your factory resonator pipe with a t.. We have redesigned our GX Series catback systems and will have them available to ship at the end of .. The exhaust system is one of the most important parts of any vehicle. It protects the driver and other nearby cars almost as much as the braking system does. If you want your car to take care of you, you need to take the best care of it.

Shelby American is proud to announce the latest generation Shelby Ford F-150 Raptor, the most polished off-road truck ever we have offered. Add more products to wishlist by simply getting registered on Eurocarparts. One of the most important elements of your car, your exhaust is vital for preventing harmful gases from being released into your surroundings. When you notice damage or wear and tear, it's essential to fix them quickly.

Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth defects or other reproductive harm. This list, which must be updated at least once a year, has grown to include approximately 900 chemicals since it was first published in 1987. RES is but one of many great vendors of parts for your car’s exhaust system. Entice customers to sign up for your mailing list with discounts or exclusive offers. I watched a ton of videos and finally found one from Edge Autosport that went through 6 different variations of ETS setups.

The 2024 Roush Super Duty stands as a testament to Roush Performance's dedication to engineering excellence, blending raw power with refined style. Whether it's for work or play, the Roush Super Duty promises to deliver an unparalleled driving experience, making every journey memorable. If the above ten reasons to consider a cat back exhaust system have you thinking it may be right for your car then Sandgate Auto Electrics are the people to call. Your neighbours may disagree that this is a benefit, but as we’ve mentioned earlier, and depending on your muffler choice, your vehicle will have a lot more grunt. This may well be the area you need to do the most research into and the sound quality, and type, can range drastically per system. At Walker, it's more than peace of mind in knowing we lead the industry with unparalleled level of compliance.

Dual Magnaflow wide open mufflers with quad 3.5" exhaust tips, slightly louder and deeper than standard Borla. This upgrade option retains the large Borla resonator and replaces Borla mufflers with dual Magnaflow mufflers and quad tips. Borla is a great exhaust, but with this upgrade your back will look much better with the large aggressive oval quad tips and will sound better too! Cat-back exhaust systems refer to all of the components that exhaust gasses flow through after exiting the vehicle’s catalytic converter.

And for early access to special offers on the products you love, add Banks Special Offers. In a world of companies making disparate parts, Banks engineers the entire engine, not just its components. The proof of Banks’ expertise is its list of national championships and world records as well as the biggest military engine contract of the century. Of all the possible options, the U.S. military chose the Banks D866T engine for its high performance and durability.

It is important to note, however, that going too large may cause a dip in performance when gases pile up and exit the system slower resulting in torque, rpm, and horsepower loss. After the emissions are channeled out from the cylinders by the exhaust manifold, they are deposited into different catalytic converters. The IE Catback Exhaust System for your Audi B9/B9.5 S4 incorporates our in-house engineered DroneTrap technology to deliver a truly aggressive exhaust note without any annoying drone or rasp. Engineered with cutting-edge design features, including mandrel-bent stainless steel, TIG welding, multi-point reinforcements, and oversized quad tips. A catback exhaust system is a type of aftermarket exhaust system that replaces the muffler and tailpipe of a vehicle. It is called a "catback" system because it starts at the catalytic converter, which is located in the middle of the...

In this article, we’ll explain what a catback exhaust system is, what it does, and why it’s different from your run-of-the-mill exhaust systems. There are seemingly endless available upgrades when looking to enhance vehicle performance. It certainly rings true when it comes to your vehicle’s exhaust system. One term that you’ve probably heard if you’re in the market for an aftermarket exhaust upgrades is cat-back exhaust. What exactly does it mean, and how does it change the way your vehicle performs? This 2009 Pontiac G8 GXP is one of approximately 1,830 examples produced, and it has 16k miles.

All performance exhaust systems are designed with you in mind, and we cater to an ever-expanding range of vehicles. Milltek believes in continuous evolution, and their research & development team work throughout the year to deliver the most in demand solutions to all your performance exhaust requirements. All products are made in the UK and distributed to more than 90 countries worldwide, making Milltek Sport one of the most accessible performance aftermarket brands on the market. If you're looking to customize your vehicle's exhaust system, Mishimoto also offers a range of aftermarket exhaust options. These exhaust systems are designed for specific vehicle models and provide a combination of performance, sound, and visual enhancements.

Noticeable gains will be noticed in the initial throttle response, with reduced turbo lag. Engine movement and exhaust weight are transferred into the exhaust hangers, which puts a lot of stress on the mount brackets. IE's catback system is manufactured with multi-point and boxed-in hanger mounts designed to stand the test of time. Drive confidently knowing your exhaust is securely mounted and protected against annoying rattles or breaks. All piping is constructed of mandrel-bent T304L stainless steel to offer superior corrosion resistance.